Glass Reactors (160-1500 ml) GR-5100 Series
Send a request
Glass Reactors (160-1500 ml) GR-5100 Series
LEGR-5100 Glass Reactors provide 160-1500 ml vessels for stirred reaction work with direct visual access. The family addresses the following operating needs:
- Stirred experiments corresponding to reactions traditionally run in a shaker. Stirring improves scalability, while the system permits higher operating temperatures and pressures and a wider range of reactor controls and instrumentation.
- Glass vessels for elevated pressure experiments, allowing the operator to observe mixing, changes in color and other visible changes in the contents.
- Convenient reactor operation at moderate pressure and/or a construction selected for corrosion resistance.
This description defines the product family. Guaranteed performance, included hardware, exclusions, interfaces and acceptance criteria are stated only in the project-specific technical proposal and approved datasheet.
Operating specifications
- Reaction vessel construction: glass or metal.
- Support arrangement: bench top stand.
- Head mounting: fixed head.
- Vessel capacity range: 160 mL to 1.5 L.
- Maximum allowable working pressure: glass 10 bar; metal 1000 psi (69 bar).
- Maximum operating temperature, ºC: 225.
O-ring seals and split-ring closures
The closure supports the glass vessel and forms the seal between the glass cylinder and metal head. A face-sealing O-ring works with a split-ring closure to make routine opening and closing straightforward. The gasket groove retains the O-ring on the head when the reactor is opened. Different O-ring materials are available so that the seal can be selected for compatibility with the reactants, reaction products and solvents.
Split-ring closure for glass vessels Split-ring closure for metal vessels The glass-vessel split ring carries high temperature plastic cushions. These cushions keep the glass from touching the metal ring directly. Tightening the six sealing screws by hand compresses the O-ring sufficiently to form the seal. Latches snap the split-ring sections together and hold the closure positively in place.
Metal cylinders use a different split ring. That closure is built for the higher working pressure permitted with the metal vessel arrangement.
High torque magnetic stirring drives
A magnetic drive powers the internal stirrer in each reactor. The drive arrangement supports dependable routine stirring.
Internal agitation options
The standard internal agitator is a turbine impeller. Its axial mixing action keeps solid particles suspended in the reaction liquid. The same impeller arrangement distributes gas through the liquid phase.
A gas entrainment impeller is an alternative when the main objective is to circulate gas from the reactor head space back through the liquid. Select this agitator where head space gas recirculation is the primary stirring requirement.
Standard head fittings
The glass reactor head carries the following fittings and internal equipment:
- A pressure gage of 3-1/2 inch diameter, with calibration scales of 0-200 psi and 0-14 bar.
- A valve for gas release.
- A valve for the gas inlet.
- A valve for taking liquid samples.
- A thermocouple inside the reactor.
- An internal cooling loop, standard for capacities from 300 mL to 1.5 L.
- An internal stirrer powered through a magnetic drive.
- Glass-cylinder heads use spring-loaded pressure relief valves. Relief settings and rupture disc ratings are provided on request for the selected vessel and operating temperature; the selected protection must not exceed the vessel MAWP.
- Internal fittings use T316 Stainless Steel with a PTFE coating.
Materials and wetted components
The glass arrangement combines a glass reaction cylinder with a metal head, internal stirrer, dip tube, thermowell and cooling loop. External valves and fittings complete this arrangement. An all metal construction is available as the alternative.
Type 316 Stainless Steel is the standard head material. Standard internal components are PTFE coated T316 SS. The head and other wetted internal parts can instead be supplied in any of the standard alternative construction materials. The ordering guide identifies the material selections.
Changing vessel capacity
Changing the cylinder and internal components converts the reactor between 160, 300, 450, and 600 mL capacities. The larger 1 L and 1.5 L vessels can likewise be interchanged within their size group.
The stand for 160-600 mL vessels cannot be converted to support the 1 and 1.5 L vessels. The larger stand can, however, be adapted to carry vessels in the 160-600 mL group. If later capacity changes are planned, choose the stand for the largest vessel that will be required. This avoids having to replace the shield and support components when changing to that capacity.
Heating arrangements and temperature regulation
Glass cylinders can be supplied with a circulating jacket or without one. A jacketed cylinder takes heat from a user supplied circulator; a non-jacketed cylinder can be heated with a removable mantle. Circulating jackets are normally selected for glass reactors because they retain visibility through the vessel wall. Some reactions require no heating, while other work may favor a removable heating mantle for operation at elevated temperature.
Transparency does not affect the selection for metal cylinders. Even so, using the same heating method for metal and glass cylinders generally allows both to share the same heating equipment and temperature control arrangement.
When a circulating bath already has its own temperature controller, the reactor can be ordered without a heating mantle. In that case a motor controller for stirring speed may be the only additional controller required. Most laboratory circulators should have sufficient capability for these small vessels. Moveable electric mantles are available for vessels without a circulating jacket. The mantles operate on 115 or 230 VAC.
Temperature and reactor controller
The reactor controller provides PC communication for all functions installed in the controller. Available functions include PID control with auto tune, Ramp and Soak programming, separate control loops for heating and cooling, and stirrer motor speed control. Further functions comprise a full or half power heater setting, a lockout relay and reset for over temperature protection, and expansion modules for a tachometer, pressure measurement and a high temperature alarm.
Automatic progression through a preset temperature profile requires the controller configuration with the corresponding programming feature. This controller operates the electric heating mantle. It does not control a user supplied circulating bath.
Separate stirring motor controller
A separate motor controller is available to set and regulate stirrer motor speed. This arrangement serves jacketed glass reactors when the user supplies a circulator with its own temperature control.
Stirrer motor choices
The reactors offer a choice of three motor arrangements:
- The standard arrangement uses a variable speed motor rated at 1/8 hp.
- The standard stirring range is 0-1700 rpm. Reversing the dual pulley doubles the available torque and reduces the speed by half.
- An explosion proof 1/4 hp motor is available on request. It also provides variable speed operation and the same stirring speed ranges as the standard motor.
- An air motor can be selected where a variable compressed air supply is available and the operator prefers the additional safety associated with a non-electrical motor.
Conversion between glass and metal cylinders
Conversion sets allow the reactor to change from a glass cylinder to a metal cylinder or from metal to glass. Each set contains the cylinder, closure, pressure gage and safety relief devices appropriate to the resulting configuration. The heating equipment is excluded from the conversion set.
Glass cylinder to metal cylinder Conversion set type Capacity, mL Starting configuration Resulting configuration Jacketed conversion set 300 Glass jacketed Metal jacketed Unjacketed conversion set 300 Glass Metal Jacketed conversion set 450 Glass jacketed Metal jacketed Unjacketed conversion set 450 Glass Metal Jacketed conversion set 600 Glass jacketed Metal jacketed Unjacketed conversion set 600 Glass Metal Unjacketed conversion set 160 Glass Metal Jacketed conversion set 1000 Glass jacketed Metal jacketed Unjacketed conversion set 1000 Glass Metal Jacketed conversion set 1500 Glass jacketed Metal jacketed Unjacketed conversion set 1500 Glass Metal Metal cylinder to glass cylinder Conversion set type Capacity, mL Starting configuration Resulting configuration Jacketed conversion set 300 Metal jacketed Glass jacketed Unjacketed conversion set 300 Metal Glass Jacketed conversion set 450 Metal jacketed Glass jacketed Unjacketed conversion set 450 Metal Glass Jacketed conversion set 600 Metal jacketed Glass jacketed Unjacketed conversion set 600 Metal Glass Unjacketed conversion set 160 Metal Glass Jacketed conversion set 1000 Metal jacketed Glass jacketed Unjacketed conversion set 1000 Metal Glass Jacketed conversion set 1500 Metal jacketed Glass jacketed Unjacketed conversion set 1500 Metal Glass Operating glass vessels under pressure
Glass pressure vessels require careful consideration of vessel design, handling practices and operator preparation. The following precautions apply to apparatus that uses glass vessels or bottles under pressure.
- Before a reaction proceeds at elevated pressure and temperature, the operator must assess every potential hazard associated with breakage of the pressurized glass vessel. Safe operation depends on accounting for the consequences of such a failure.
- The glass vessel itself requires rounded sections, correct annealing and cushioned supports. Its design must accommodate differential thermal expansion. Sufficient wall thickness, careful manufacture, inspection and testing are also necessary. Test pressure and inspection documentation for the selected glass vessel are available on request.
- Maintenance and handling are equally significant. A scratch in a ductile metal vessel may be cosmetic, but a scratch in brittle glass creates a severe stress concentration. Such damage can destroy the vessel's structural integrity. Handle and wash glass cylinders with particular care to preserve the integrity of the vessel.
- Operators must receive training to recognize the hazards. Suitable safety provisions must remain in place and fully operational whenever the equipment is used.
Dimensional and operating data
Vessel configuration 300 mL fixed head 450 mL fixed head 600 mL fixed head 160 mL fixed head 1000 mL fixed head 1500 mL fixed head Nominal internal volume, mL 300 450 600 160 1000 1500 Glass vessel maximum allowable working pressure (MAWP) 10 bar Metal vessel maximum allowable working pressure (MAWP) 1000 psi (69 bar) Operating temperature limits FKM O-ring seal 225 °C Glass vessel with FFKM O-ring seal 225 °C Metal vessel with FFKM O-ring seal 225 °C Reactor construction and equipment Head mounting arrangement Fixed head Support arrangement Bench top Closure arrangement Glass vessels: 6 thumb screws; metal vessels: split-ring closure with 6 thumb screws Valve connection threads 1/8″ Male NPT Magnetic stirring coupling Magnetic drive Torque limit 16 Inch-Pounds Impeller quantity, 4-blade 1 2 2 1 2 2 Stirring motor rating 1/8 hp, variable speed Pressure gage diameter 3.5 inches Gage range for glass cylinder 0-200 psi (14 bar) Gage range for metal cylinder 0-1000 psi (69 bar) Temperature sensing arrangement Fixed Type J thermocouple Cooling coil provision Single loop supplied None Single loop supplied Heating arrangement Mantle heater Glass vessel heating power, Watts 510 590 780 400 400 550 Metal vessel heating power, Watts 510 590 780 400 450 650 Electrical service requirements Supply voltage, Volts, AC 115 / 230 Maximum current, amps, 115 / 230 9 / 5 Cylinder measurements Internal diameter x depth, inches 2.5 x 4.0 2.5 x 6.0 2.5 x 8.0 2.5 x 2.0 4.0 x 6.0 4.0 x 8.0 Assembled glass vessel weight, pounds 15 15 16 14 29 28 Assembled metal vessel weight, pounds 18 19 21 16 33 36 Glass cylinder-only weight, pounds 0.8 1.1 1.4 0.5 3.0 4.1 Metal cylinder-only weight, pounds 3.4 4.6 5.9 2.2 8.3 10.8 Reactor and support measurements Width x depth excluding controller, inches 17 x 24 21 x 26 Overall height, inches 30 33 Overall weight, pounds 60 63 66 60 109 113 Replacement parts set Spare parts kit for smaller vessels Spare parts kit for larger vessels Reactors and pressure vessels can be supplied with a wide range of options and accessories. With them the user can configure the system for the planned reactions and the intended operating conditions. The available options and accessories are listed below:
- Automated liquid sampler
- Catalyst addition devices
- Catalyst baskets
- Catalyst loading toolkit
- Catalyst testing system
- Condensers
- Coned pressure fittings
- Continuous bulk-solids feeder
- Controllers
- Cooling coils
- Equipment for use in potentially ignitable atmospheres
- External valves and fittings
- Gas measurement systems:
- Intermediate supply tanks
- Mass flow
- High pressure gas burettes
- Heaters
- Insulated electrical glands
- Liners
- Liquid charging systems:
- Liquid metering pumps
- Liquid charging pipettes
- Magnetic drives
- Motors and drives
- Pressure gages
- Pressure hose
- Safety rupture discs
- Sample collection vessel
- Service fixtures
- Solids/slurry addition devices
- Spare parts kits
- Split-ring closures
- Stirrer options
- Gas entrainment impellers
- Thermocouples
- Valves and fittings:
- Bottom drain valves
- Manual control valves for compressed gas tanks
- Pressure relief valves
- Safety check valves
- Windows
The standard construction material for reactors is Type 316 Stainless Steel. Other alloys are also available. Reactors can be built from the following materials:
- Type 316/316L Stainless Steel
- Alloy A-286
- Alloy 20
- Alloy 230
- Alloy 400
- Alloy 600
- Alloy 625
- Alloy B-2/B-3
- Alloy C-276
- Nickel 200
- Titanium Grades 2, 3, 4 and 7
- Zirconium 702 and 705
If a special alloy is specified for a reactor, the head, the cylinder and every internal wetted part of the vessel are made from that alloy. The external valves and fittings remain stainless steel. External parts are normally not exposed to the corrosive conditions present inside the vessel, so the extra cost of making them from special alloys is rarely justified.
Alloy Designation
The corrosion resistant alloys available for reactors and pressure vessels are identified here by alloy designation numbers. The same alloys are also known by trade names and by ASTM, ASME, DIN and other specification numbers. Many high nickel alloys were first patented and sold under trade names such as Monel, Inconel, Incoloy, Carpenter Alloy 20 and Hastelloy. Most of those patents have now expired. These alloys are now supplied as construction materials by other reputable producers as well as by the owners of the original trade names.
Among the many corrosion resistant alloys on the market, two or three may have very similar compositions and serve the same corrosive environment. Each alloy still has its own physical strength, its own temperature characteristics and its own particular resistance to certain corrosive media. All of these factors have to be weighed when an alloy is selected, and cost and availability also influence the final choice.
- MONEL, INCONEL and INCOLOY are registered trademarks of Special Metals Corp.
- CARPENTER 20 is a registered trademark of Carpenter Technology Corporation.
- HASTELLOY is a registered trademark of Haynes International, Inc.
The table below gives the basic composition of these alloys. Data on corrosion resistance is available in corrosion handbooks and metallurgical publications. The individual alloy producers are also a useful source of information.
Any short listing of the corrosion resistance of metals and alloys can mislead, because it cannot cover every effect of concentration, temperature, pressure and the presence of additional ions. Each of these has a significant effect on how well a reactor withstands corrosion. The susceptibility of a material to stress corrosion cracking, intergranular corrosion and pitting must also be taken into account when judging whether the material suits a particular application.
The main characteristics of the construction materials offered are summarized below. These summaries are only a starting point for any study of comparative corrosion resistance and physical properties. Booklets from the material manufacturers on each alloy are available on request. Further details can also be found in other sources.
Nominal Chemical Composition of Pressure Vessel Materials Major Elements (Percent) Material Typical Trade Name Fe Ni Cr Mo Mn Other T316 Stainless Steel 65 12 17 2.5 2.0 Si 1.0 Alloy 20 Carpenter 20 35 34 20 2.5 2.0 Cu 3.5, Cb 1.0 max Alloy 230 Haynes 230 3 52 22 2 0.7 Co-5, W-14, Si-0.5 Alloy 400 Monel 400 2.5 max 63 min 2 max Cu 31.5 Alloy 600 Inconel 600 8 76 15.5 Alloy 625 Gr1 Inconel 625 Gr1 5 58 22 9 0.5 Cb+Ta 3.7 Alloy A-286 Alloy 286 53 25 15 1.2 2 Si-1, Ti-2.1, Al-0.35 Alloy B-2/B-3 Hastelloy B-2/B-3 2 66 1 28 1 Co 1.0 Alloy C-276 Hastelloy C-276 6.5 53 15.5 16 1 W4.0, Co 2.5 Nickel 200 99 Titanium Grade 2, 3, 4 Commercially pure titanium Ti 99 min Titanium Grade 7 Ti 98.8 min, 0.15 Pd Zirconium Grade 702 Zr + Hf 99.2 min, Hf 4.5 max Zirconium Grade 705 Zr + Hf 95.5 min, Hf 4.5 max, Nb 2.5 Type 316/316L Stainless Steel
Type 316 Stainless Steel performs very well with most organic systems. Under certain conditions a few organic acids and organic halides can hydrolyze and form inorganic halogen acids, and these attack T316SS. Acetic acid, formic acid and other organic acids are handled in T316SS as a matter of routine.
T316SS is not usually the preferred material for inorganic acid systems. At ambient temperature it gives useful resistance to dilute sulfuric, sulfurous, phosphoric and nitric acids. At elevated temperature and pressure, however, sulfuric, phosphoric and nitric acids attack T316SS readily. Halogen acids attack every form of stainless steel quickly, even in dilute solutions and at low temperature.
T316SS resists surface corrosion by caustics very well, but caustics can cause stress corrosion cracking in stainless pressure vessels. This effect starts to appear just above 100 °C and has been the most frequent cause of corrosion failure in stainless laboratory vessels. T316SS resists ammonia and most ammonia compounds well.
Halogen salts can cause severe pitting in every stainless steel. Chlorides can cause stress corrosion cracking. Many other salt solutions, especially neutral or alkaline salts, can be handled in stainless vessels.
At moderate temperature and pressure, T316SS is suitable for most commercial gases. In strictly anhydrous systems, even hydrogen chloride, hydrogen fluoride and chlorine can be handled in stainless steel.
Practically all T316SS produced today also meets the specifications for T316L, the low carbon grade of stainless steel.
Alloy 20
Alloy 20 is an enriched stainless steel grade developed specifically for dilute sulfuric acid (up to 30 percent by weight) at elevated temperatures. It also suits nitric and phosphoric acid systems, as well as every system for which T316SS is suitable.
Alloy 400
Alloy 400 consists essentially of two-thirds nickel and one-third copper. In many applications its corrosion resistance is about equal to that of nickel. It allows higher maximum working pressures and temperatures and costs less, because it is much easier to machine.
Alloy 400 is widely used with caustic solutions, since in most applications it does not suffer stress corrosion cracking. Chloride salts do not cause stress corrosion cracking in Alloy 400 either. It is also a very good material for fluorine, hydrogen fluoride and hydrofluoric acid systems. Alloy 400 has some resistance to hydrochloric and sulfuric acids at moderate temperatures and concentrations, but it is rarely the first choice for these acids. As its high copper content suggests, nitric acid and ammonia systems attack Alloy 400 rapidly.
Alloy 600
Alloy 600 is a high nickel alloy. It resists caustics and chlorides very well at high temperature and high pressure when sulfur compounds are present. In caustic environments no alloy performs better than Alloy 600. It is also often selected for its high strength at elevated temperatures. It can be recommended for a wide range of corrosive conditions, but its cost usually restricts its use to applications that need its exceptional properties.
Alloy B-2/B-3
Alloy B-2/B-3 is rich in nickel and molybdenum and was developed mainly to resist reducing acid environments, especially hydrochloric, sulfuric and phosphoric acids. In their pure forms it resists these acids better than any other alloy. Ferric ions and other oxidizing ions, even at levels as low as 50 ppm, can sharply reduce the resistance of this alloy.
Alloy C-276
Alloy C-276 is a nickel chromium-molybdenum alloy that probably has the widest general corrosion resistance of all commonly used alloys. It was first developed for wet chlorine service. It also resists strong oxidizers such as cupric and ferric chlorides very well, as well as many chlorine compounds and materials contaminated with chlorine. Thanks to this wide chemical resistance, Alloy C-276 is the second most widely used alloy after T316SS for research and development vessels.
Nickel 200
Nickel 200 is one designation of commercially pure nickel. It gives the highest corrosion resistance in hot caustic environments. Its use is strongly limited, however, by poor machinability and the high fabrication cost that follows from it.
Titanium
Titanium performs very well with oxidizing agents such as nitric acid, aqua regia and other mixed acids. It also resists chloride ions very well. Reducing acids such as sulfuric and hydrochloric acid corrode titanium at unacceptably high rates in pure form. These rates can drop to acceptable levels when relatively small amounts of oxidizing ions, such as cupric, ferric or nickel ions, or even nitric acid, are present and act as corrosion inhibitors.
This effect has led to many successful uses of titanium in hydrometallurgy, where acids, especially sulfuric acid, are used to leach ores. In these processes the extracted ions act as corrosion inhibitors.
Users must keep in mind that titanium burns vigorously in oxygen at elevated temperatures and pressures. Many hydrometallurgy applications handle oxygen and sulfuric acid successfully in titanium equipment, but the risk of ignition is always present. Protection against it is required whenever titanium and oxygen are used together.
Commercially pure titanium comes in several grades. Grade 2 is the grade most often used for industrial equipment, because it can be welded. Vessels in Grade 2 can be built to the PED and ASME Codes on request. Grade 4 has slightly higher trace levels of iron and oxygen and is stronger than Grade 2. Grade 4 cannot be welded and is outside the PED and ASME Codes, so code design on request applies to Grade 2 only.
Most vessels are not welded, so Grade 4 can give higher working pressures than Grade 2. Grade 7 contains small amounts of palladium. It gives improved resistance in certain environments and can be used for reactors and pressure vessels when suitable billets are available.
Zirconium
Zirconium resists hydrochloric and sulfuric acids very well. As with Alloy B-2/B-3, oxidizing ions such as ferric and cupric ions and fluorides must be avoided. Zirconium also resists phosphoric and nitric acids and alkaline solutions well. Two grades are available. Grade 702 contains hafnium and is the standard commercial grade, with the best resistance to most corrosive agents. Grade 705 contains small amounts of both hafnium and niobium. These additions raise its strength and permit higher maximum working pressures for a vessel. Grade 702 usually resists corrosion better than Grade 705, and Grade 702 is also easier to obtain from commercial raw material stocks.
High Temperature / High Strength Alloys
Besides the metals selected for corrosion resistance, some alloys are offered for their outstanding strength, their strength at high temperature, or both.
Alloy 230
Alloy 230 is listed among the alloys approved in ASME Section II for pressure vessel design. It is high in nickel, chromium, tungsten and cobalt. Its resistance is similar to that of Alloy 600, but it is normally chosen for its high strength at very high temperatures. It is sometimes chosen as a bolting material.
Alloy 625
Alloy 625 has chemical resistance similar to Alloy C-276, but is much stronger. It is used to obtain higher pressure ratings in high temperature applications.
Alloy A-286
Alloy A-286 belongs to the stainless steel family and keeps very high strength up to 371 °C. It is widely used as a bolting material.
Pressure and Temperature Limits
The maximum pressure and temperature for any reactor or pressure vessel depend on the vessel design, its construction material and the other components that form part of the design. Every material loses strength as temperature rises, so a pressure rating is only meaningful together with the temperature at which it applies. The ratings in the specification tables give the maximum allowable working pressure (MAWP) of each vessel in pounds per square inch (psi) and in bar, at the maximum rated temperature of that design, for a vessel made of Type 316 Stainless Steel. For vessels made of other alloys, the maximum pressure and temperature limits are calculated and assigned by engineering in line with all applicable regulations.
A lower operating temperature can sometimes allow a higher working pressure. For example, the high temperature (HT) version of one reactor series is rated at 2000 psi (138 bar) maximum pressure and 500 °C maximum temperature. The standard version of the same series is rated at 2900 psi (200 bar) maximum pressure at 350 °C maximum temperature.
It must not be assumed that a vessel operated at a lower temperature can be used above its rated MAWP. The rating may be governed by factors other than the strength of the vessel wall. The closure design, the magnetic drive, the seal type, the other components selected and the construction material can all limit the pressure and temperature ratings.
As the table below shows, the maximum operating temperature of some materials is much lower than the value allowed for stainless steel.
Maximum Allowable Temperatures Materials of Construction Maximum Temperature T316/316L Stainless Steel on request Alloy 20 426 °C Alloy 230 on request Alloy 400 482 °C Alloy 600 on request Alloy 625 Gr 1 648 °C Alloy A-286 371 °C Alloy B-2/B-3 426 °C Alloy C-276 on request Nickel 200 315 °C Titanium Grade 2, 3, 4 and 7 315 °C Zirconium Grade 702 and 705 371 °C Safe calculation of the maximum working pressures and temperatures of reactors and pressure vessels involves multiple factors.













