Floor Stand Stirred Reactors (50 & 100 l) FSSR-8500 Series
Send a request
Floor Stand Stirred Reactors (50 & 100 l) FSSR-8500 Series
LEFSSR-8500 floor stand stirred reactors have 50 L or 100 L capacities for scale-up experiments and pilot work. Their volumes lie between laboratory reactors and conventional production-scale stirred equipment.
A Reactor Controller with its associated 3 zone slave box regulates electric band heaters. Alternatively, a jacket welded to the outside of the cylinder permits temperature control through a circulator.
Base units carry a pressure rating of 725 psi (50 bar). Higher pressure ratings are available on request. Construction can use a range of commercially available alloys selected for corrosion resistance.
This description defines the product family. Guaranteed performance, included hardware, exclusions, interfaces and acceptance criteria are stated only in the project-specific technical proposal and approved datasheet.
Operating features
- Maximum allowable working pressure (MAWP): 725 psi (50 bar).
- Operating temperature ceiling: 200 °C.
- Temperature regulation by PID control with programmed ramp and soak stages.
- Variable speed motor coupled to a gear drive.
- Heating by a three zone band heater or welded jacket.
- Reactor head hoist, with manual and electric versions available.
- Bottom drain valve, with actuated and manually operated versions available.
- Thermocouple for temperature control.
Standard head equipment and internal components
- Head sealing with an FKM O-ring.
- Magnetic drive in extra heavy duty construction.
- Stirring shaft with stirrer assembly.
- Safety assembly with rupture disc.
- Pressure gage, with a pressure relief valve available as an option.
- Needle valves for gas inlet and gas release.
- External assembly for charging solids.
- Cooling coil of spiral geometry.
- Custom configuration options are available.
System capacity 50 L 100 L Maximum allowable working pressure (MAWP) 725 psi (50 bar) Operating temperature ceiling 200 ˚C Electrical service requirements 230V, 1P or 400-415 V 3-Phase “WYE”, 8 kW 400-415 V 3-Phase “WYE”, 10 kW Cylinder / head weights, T316 SS 350/175 lbs (160/80 kg) 575/275 lbs (260/125 kg) Cylinder internal diameter x depth 13 x 24 in (33 x 61 cm) 16 x 32 in (40 x 81 cm) Support height x width x depth 120 x 90 x 40 in (3.1 x 2.3 x 1.0 m) The standard construction material for reactors is Type 316 Stainless Steel. Other alloys are also available. Reactors can be built from the following materials:
- Type 316/316L Stainless Steel
- Alloy A-286
- Alloy 20
- Alloy 230
- Alloy 400
- Alloy 600
- Alloy 625
- Alloy B-2/B-3
- Alloy C-276
- Nickel 200
- Titanium Grades 2, 3, 4 and 7
- Zirconium 702 and 705
If a special alloy is specified for a reactor, the head, the cylinder and every internal wetted part of the vessel are made from that alloy. The external valves and fittings remain stainless steel. External parts are normally not exposed to the corrosive conditions present inside the vessel, so the extra cost of making them from special alloys is rarely justified.
Alloy Designation
The corrosion resistant alloys available for reactors and pressure vessels are identified here by alloy designation numbers. The same alloys are also known by trade names and by ASTM, ASME, DIN and other specification numbers. Many high nickel alloys were first patented and sold under trade names such as Monel, Inconel, Incoloy, Carpenter Alloy 20 and Hastelloy. Most of those patents have now expired. These alloys are now supplied as construction materials by other reputable producers as well as by the owners of the original trade names.
Among the many corrosion resistant alloys on the market, two or three may have very similar compositions and serve the same corrosive environment. Each alloy still has its own physical strength, its own temperature characteristics and its own particular resistance to certain corrosive media. All of these factors have to be weighed when an alloy is selected, and cost and availability also influence the final choice.
- MONEL, INCONEL and INCOLOY are registered trademarks of Special Metals Corp.
- CARPENTER 20 is a registered trademark of Carpenter Technology Corporation.
- HASTELLOY is a registered trademark of Haynes International, Inc.
The table below gives the basic composition of these alloys. Data on corrosion resistance is available in corrosion handbooks and metallurgical publications. The individual alloy producers are also a useful source of information.
Any short listing of the corrosion resistance of metals and alloys can mislead, because it cannot cover every effect of concentration, temperature, pressure and the presence of additional ions. Each of these has a significant effect on how well a reactor withstands corrosion. The susceptibility of a material to stress corrosion cracking, intergranular corrosion and pitting must also be taken into account when judging whether the material suits a particular application.
The main characteristics of the construction materials offered are summarized below. These summaries are only a starting point for any study of comparative corrosion resistance and physical properties. Booklets from the material manufacturers on each alloy are available on request. Further details can also be found in other sources.
Nominal Chemical Composition of Pressure Vessel Materials Major Elements (Percent) Material Typical Trade Name Fe Ni Cr Mo Mn Other T316 Stainless Steel 65 12 17 2.5 2.0 Si 1.0 Alloy 20 Carpenter 20 35 34 20 2.5 2.0 Cu 3.5, Cb 1.0 max Alloy 230 Haynes 230 3 52 22 2 0.7 Co-5, W-14, Si-0.5 Alloy 400 Monel 400 2.5 max 63 min 2 max Cu 31.5 Alloy 600 Inconel 600 8 76 15.5 Alloy 625 Gr1 Inconel 625 Gr1 5 58 22 9 0.5 Cb+Ta 3.7 Alloy A-286 Alloy 286 53 25 15 1.2 2 Si-1, Ti-2.1, Al-0.35 Alloy B-2/B-3 Hastelloy B-2/B-3 2 66 1 28 1 Co 1.0 Alloy C-276 Hastelloy C-276 6.5 53 15.5 16 1 W4.0, Co 2.5 Nickel 200 99 Titanium Grade 2, 3, 4 Commercially pure titanium Ti 99 min Titanium Grade 7 Ti 98.8 min, 0.15 Pd Zirconium Grade 702 Zr + Hf 99.2 min, Hf 4.5 max Zirconium Grade 705 Zr + Hf 95.5 min, Hf 4.5 max, Nb 2.5 Type 316/316L Stainless Steel
Type 316 Stainless Steel performs very well with most organic systems. Under certain conditions a few organic acids and organic halides can hydrolyze and form inorganic halogen acids, and these attack T316SS. Acetic acid, formic acid and other organic acids are handled in T316SS as a matter of routine.
T316SS is not usually the preferred material for inorganic acid systems. At ambient temperature it gives useful resistance to dilute sulfuric, sulfurous, phosphoric and nitric acids. At elevated temperature and pressure, however, sulfuric, phosphoric and nitric acids attack T316SS readily. Halogen acids attack every form of stainless steel quickly, even in dilute solutions and at low temperature.
T316SS resists surface corrosion by caustics very well, but caustics can cause stress corrosion cracking in stainless pressure vessels. This effect starts to appear just above 100 °C and has been the most frequent cause of corrosion failure in stainless laboratory vessels. T316SS resists ammonia and most ammonia compounds well.
Halogen salts can cause severe pitting in every stainless steel. Chlorides can cause stress corrosion cracking. Many other salt solutions, especially neutral or alkaline salts, can be handled in stainless vessels.
At moderate temperature and pressure, T316SS is suitable for most commercial gases. In strictly anhydrous systems, even hydrogen chloride, hydrogen fluoride and chlorine can be handled in stainless steel.
Practically all T316SS produced today also meets the specifications for T316L, the low carbon grade of stainless steel.
Alloy 20
Alloy 20 is an enriched stainless steel grade developed specifically for dilute sulfuric acid (up to 30 percent by weight) at elevated temperatures. It also suits nitric and phosphoric acid systems, as well as every system for which T316SS is suitable.
Alloy 400
Alloy 400 consists essentially of two-thirds nickel and one-third copper. In many applications its corrosion resistance is about equal to that of nickel. It allows higher maximum working pressures and temperatures and costs less, because it is much easier to machine.
Alloy 400 is widely used with caustic solutions, since in most applications it does not suffer stress corrosion cracking. Chloride salts do not cause stress corrosion cracking in Alloy 400 either. It is also a very good material for fluorine, hydrogen fluoride and hydrofluoric acid systems. Alloy 400 has some resistance to hydrochloric and sulfuric acids at moderate temperatures and concentrations, but it is rarely the first choice for these acids. As its high copper content suggests, nitric acid and ammonia systems attack Alloy 400 rapidly.
Alloy 600
Alloy 600 is a high nickel alloy. It resists caustics and chlorides very well at high temperature and high pressure when sulfur compounds are present. In caustic environments no alloy performs better than Alloy 600. It is also often selected for its high strength at elevated temperatures. It can be recommended for a wide range of corrosive conditions, but its cost usually restricts its use to applications that need its exceptional properties.
Alloy B-2/B-3
Alloy B-2/B-3 is rich in nickel and molybdenum and was developed mainly to resist reducing acid environments, especially hydrochloric, sulfuric and phosphoric acids. In their pure forms it resists these acids better than any other alloy. Ferric ions and other oxidizing ions, even at levels as low as 50 ppm, can sharply reduce the resistance of this alloy.
Alloy C-276
Alloy C-276 is a nickel chromium-molybdenum alloy that probably has the widest general corrosion resistance of all commonly used alloys. It was first developed for wet chlorine service. It also resists strong oxidizers such as cupric and ferric chlorides very well, as well as many chlorine compounds and materials contaminated with chlorine. Thanks to this wide chemical resistance, Alloy C-276 is the second most widely used alloy after T316SS for research and development vessels.
Nickel 200
Nickel 200 is one designation of commercially pure nickel. It gives the highest corrosion resistance in hot caustic environments. Its use is strongly limited, however, by poor machinability and the high fabrication cost that follows from it.
Titanium
Titanium performs very well with oxidizing agents such as nitric acid, aqua regia and other mixed acids. It also resists chloride ions very well. Reducing acids such as sulfuric and hydrochloric acid corrode titanium at unacceptably high rates in pure form. These rates can drop to acceptable levels when relatively small amounts of oxidizing ions, such as cupric, ferric or nickel ions, or even nitric acid, are present and act as corrosion inhibitors.
This effect has led to many successful uses of titanium in hydrometallurgy, where acids, especially sulfuric acid, are used to leach ores. In these processes the extracted ions act as corrosion inhibitors.
Users must keep in mind that titanium burns vigorously in oxygen at elevated temperatures and pressures. Many hydrometallurgy applications handle oxygen and sulfuric acid successfully in titanium equipment, but the risk of ignition is always present. Protection against it is required whenever titanium and oxygen are used together.
Commercially pure titanium comes in several grades. Grade 2 is the grade most often used for industrial equipment, because it can be welded. Vessels in Grade 2 can be built to the PED and ASME Codes on request. Grade 4 has slightly higher trace levels of iron and oxygen and is stronger than Grade 2. Grade 4 cannot be welded and is outside the PED and ASME Codes, so code design on request applies to Grade 2 only.
Most vessels are not welded, so Grade 4 can give higher working pressures than Grade 2. Grade 7 contains small amounts of palladium. It gives improved resistance in certain environments and can be used for reactors and pressure vessels when suitable billets are available.
Zirconium
Zirconium resists hydrochloric and sulfuric acids very well. As with Alloy B-2/B-3, oxidizing ions such as ferric and cupric ions and fluorides must be avoided. Zirconium also resists phosphoric and nitric acids and alkaline solutions well. Two grades are available. Grade 702 contains hafnium and is the standard commercial grade, with the best resistance to most corrosive agents. Grade 705 contains small amounts of both hafnium and niobium. These additions raise its strength and permit higher maximum working pressures for a vessel. Grade 702 usually resists corrosion better than Grade 705, and Grade 702 is also easier to obtain from commercial raw material stocks.
High Temperature / High Strength Alloys
Besides the metals selected for corrosion resistance, some alloys are offered for their outstanding strength, their strength at high temperature, or both.
Alloy 230
Alloy 230 is listed among the alloys approved in ASME Section II for pressure vessel design. It is high in nickel, chromium, tungsten and cobalt. Its resistance is similar to that of Alloy 600, but it is normally chosen for its high strength at very high temperatures. It is sometimes chosen as a bolting material.
Alloy 625
Alloy 625 has chemical resistance similar to Alloy C-276, but is much stronger. It is used to obtain higher pressure ratings in high temperature applications.
Alloy A-286
Alloy A-286 belongs to the stainless steel family and keeps very high strength up to 371 °C. It is widely used as a bolting material.
Pressure and Temperature Limits
The maximum pressure and temperature for any reactor or pressure vessel depend on the vessel design, its construction material and the other components that form part of the design. Every material loses strength as temperature rises, so a pressure rating is only meaningful together with the temperature at which it applies. The ratings in the specification tables give the maximum allowable working pressure (MAWP) of each vessel in pounds per square inch (psi) and in bar, at the maximum rated temperature of that design, for a vessel made of Type 316 Stainless Steel. For vessels made of other alloys, the maximum pressure and temperature limits are calculated and assigned by engineering in line with all applicable regulations.
A lower operating temperature can sometimes allow a higher working pressure. For example, the high temperature (HT) version of one reactor series is rated at 2000 psi (138 bar) maximum pressure and 500 °C maximum temperature. The standard version of the same series is rated at 2900 psi (200 bar) maximum pressure at 350 °C maximum temperature.
It must not be assumed that a vessel operated at a lower temperature can be used above its rated MAWP. The rating may be governed by factors other than the strength of the vessel wall. The closure design, the magnetic drive, the seal type, the other components selected and the construction material can all limit the pressure and temperature ratings.
As the table below shows, the maximum operating temperature of some materials is much lower than the value allowed for stainless steel.
Maximum Allowable Temperatures Materials of Construction Maximum Temperature T316/316L Stainless Steel on request Alloy 20 426 °C Alloy 230 on request Alloy 400 482 °C Alloy 600 on request Alloy 625 Gr 1 648 °C Alloy A-286 371 °C Alloy B-2/B-3 426 °C Alloy C-276 on request Nickel 200 315 °C Titanium Grade 2, 3, 4 and 7 315 °C Zirconium Grade 702 and 705 371 °C Safe calculation of the maximum working pressures and temperatures of reactors and pressure vessels involves multiple factors.

























