Heaters for Stirred Reactors
Send a request
Heaters for Stirred Reactors
LEHTRS electrical heaters provide standard heating for stirred reactors throughout the equipment range. Heater construction is selected for each reactor according to its operating needs, required heating load and expected temperature range. The specification table for each reactor model identifies the standard heater type and its power rating.
This description defines the product family. Guaranteed performance, included hardware, exclusions, interfaces and acceptance criteria are stated only in the project-specific technical proposal and approved datasheet.
Band Heaters Clamped to the Vessel
Clamp-on band heaters usually serve very small reactors. These vessels have little external surface available for heating, so the heater must provide high watt density and transfer heat effectively through that limited area.
Rigid Mantle Heaters
A rigid mantle consists of quartz fabric inside an aluminum shell. It is used on medium-sized reactors whose arrangement permits the heater to be moved onto or off the vessel. The mantle is light and easy to handle. It does not carry the vessel weight, and its usual operating range is limited to 350 °C or below.
Sheathed Tubular Element Heaters
These heaters contain durable, sheathed tubular heating elements within a metal shell. They serve medium and large reactors at operating temperatures up to 350 °C. In some arrangements the shell also forms part of the reactor support. The elements can be replaced readily, which is a useful maintenance feature of this heater construction.
Ceramic Body Heaters
A shaped ceramic body contains the embedded electric element, and an insulated metal housing surrounds that body. This special-purpose construction is used for reactors intended to operate at temperatures up to 600 °C. It is also used in large heaters with several independently arranged heating zones.
Alternative and Custom Heating Arrangements
Several heater constructions can replace the standard heater normally supplied with a reactor. Most of these alternatives can also be applied to non-stirred pressure vessels. The following sections explain their construction, operating characteristics and typical applications so that the heater arrangement can be selected for the vessel duty.
Heaters Machined from Aluminum Blocks
An aluminum block heater is an option for vessels of two gallons or less. The heater body is machined from a solid aluminum block, with wells for the heating elements machined into its walls. Machined channels for cooling can also be included as an option.
This arrangement provides direct electrical control of heat input without the hot-oil plumbing required by a circulating jacket. The heating elements, their wiring and the cooling channels are contained within the machined aluminum enclosure. The block distributes heat evenly, physically separates the electrical connections from the surroundings and allows rapid cooling when required.
Suitability for potentially ignitable atmospheres (Hazardous Locations) is not claimed for the standard heater. Any such arrangement is available on request and is reviewed as a complete system, including the surface-temperature limiting device and the external wiring. The integral cooling channels can also help control some exothermic reactions where cooling inside the vessel is unavailable. These channels provide external heat removal through the same block used for electrical heating.
Flexible Fabric Mantles
Flexible mantles can be supplied for a range of vessel applications. Their heating arrangement is similar to that of a rigid mantle, but they have no enclosing aluminum shell. A flexible fabric outer case provides electrical and thermal insulation. The mantle can be split and laced around projections on the vessel, making it useful for irregular vessel shapes, including cylinders with windows in their walls.
Like a rigid mantle, a flexible mantle can produce temperatures up to 350 °C. Its watt density is limited to 10 watts per square inch. A mantle can be made to cover any vessel in the range, and this construction is sometimes preferred for duties requiring only moderate temperature. The fabric case has no provision for attaching an electrical ground wire, so the electrical protection arrangement for the complete heater is reviewed before use.
Jackets for Circulating Heating and Cooling Media
A jacket can be welded to the outside wall of most pressure vessels. Hot or cold liquid, or steam, circulates through the jacket to heat or cool the vessel. This arrangement is useful when laboratory operation needs to reproduce plant conditions using a jacketed reactor similar to the plant equipment.
The jacket contains no electrical components. Its maximum temperature can be limited by controlling the temperature of the circulating medium, so use of a jacketed arrangement in a hazardous atmosphere is available on request after review of the complete system. The heating medium directly contacts the vessel wall, allowing rapid and even heat transfer. Controlling that medium's temperature also helps avoid temperature overshoot when processing sensitive materials.
Standard jackets have an internal operating pressure limit of 100 psig (7 bar). A jacket with a higher pressure rating can be provided when required. The pressure rating applies within the jacket, while the circulating medium supplies the heating or cooling duty.











